This standard is issued under the fixed designation F; the number immediately 1 This test method is under the jurisdiction of ASTM Committee F06 on. 8 Oct ASTM F is an excellent test for determining the actual moisture condition of a slab. As a result, this type of test is recommended by many. ASTM F Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes. Specifications, Standards & Certificates.
|Country:||Bosnia & Herzegovina|
|Published (Last):||17 January 2004|
|PDF File Size:||11.21 Mb|
|ePub File Size:||17.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
General contractors must bear in mind two interactive processes when astm f2170 are looking at construction schedules: Additionally, no in-situ probe should be left in concrete for more than 30 days without a calibration check, according to the standard.
When To Test Concrete To ASTM F2170?
In that case, astm f2170 did not allow the slab sufficient time for concrete moisture levels to equilibrate f21770 equilibrium moisture content according to relative humidity RH. We have people who use the Rapid RH on shallow pours. Topics moisture meters Flooring 62 Moisture Meter 56 Moisture Content 45 productivity 39 Wood Flooring 37 restoration professionals 36 woodwork 36 concrete 29 hay 25 moisture meter manufacturer 22 ASTM 16 home inspection 16 restoration project astm f2170 RH 15 thermo-hygrometer astm f2170 Equilibrium Moisture Content 12 EMC 11 Moisture meter accuracy 11 Thermo-Hygrometers 8 gypsum asym Water Damage 6 grain moisture tester 6 wallboard 5 grain 4 moisture detection 4 reduce stress 4 soil 4 Hops Harvesting 3 cotton 3 flooring system 3 pinless moisture meters 3 Flooring Failures 2 IWF Tradeshow astm f2170 NWFA 2 leather 2 paper astm f2170 winter restoration 2 Fire Damage 1 building inspector tools 1 burnout 1 condensation control 1 drywall moisture meter 1 humidity sensor 1 see all.
It has been believed that the change in astm f2170 desiccant weight could be translated into a moisture ratio for the concrete beneath.
The MVER is defined as the rate of water vapor emissions from the surface of concrete and is determined with the use of a desiccant material sealed to the slab surface for a specified time period, then measured. A moisture map of astm f2170 entire floor can be built up, showing astm f2170 wet the slab is and where the wettest locations are. June 9, at 1: Skip to content Concrete astm f2170 moisture is a major cause of concrete flooring failure.
Sub-grade water vapor can permeate even well-mixed and applied slabs.
That being said, I have heard a couple of different methods people are using. The total area of the slab and the astm f2170 of test holes must be recorded astm f2170 your report. Finally, for best results, the combination of ASTM F non-destructive moisture content testing and Ast, in-situ relative humidity testing allows for a more complete picture of the moisture conditions of the slab.
These in-situ probes that are left in the concrete are then attached to an RH meter also known as a thermo-hygrometer to astm f2170 readings astm f2170 the moisture conditions deep in the slab. Concrete slab moisture problems can cause floor covering delamination, peeling, blistering, staining and sweating.
Map astm f2170 sensor count and location. If i have an area of approx astm f2170 ft and have done the required testing for the area, and 5 fail and 3 pass does the whole area fail?
Some calibration restrictions may apply, so read the standard carefully to be sure your test equipment qualifies for the most recent standard.
The depth is calculated to the bottom of the test hole the location of the installed RH sensor or probe. In-situ probes deepen concrete moisture measurement. Posted by Tom Laurenzi on Nov 23, While any professional must understand the exact requirements of standard F the most recent versionastm f2170 following are 10 guidelines to help ensure that you have met the criteria laid out in ASTM F If condensation occurs during the test period, then the sensor will continue to indicate that the slab is wetter than it actually is, even if the concrete has subsequently dried.
Use our checklist to record and report the RH readings. The standard provides precise guidelines for RH testing methods. With all areas astm f2170 ASTM-compliant Astm f2170 testing, precision is key and data integrity must also be astm f2170 focus for each flooring professional.
In situ moisture measurement systems are evolving rapidly as a result of Astm f2170 F and reflect the industry realities of the concrete installation business.
Leave a Reply Cancel reply Awtm email address will not be published. ASTM F is an excellent astm f2170 for determining the actual moisture condition of a slab. Section 9 of the standard requires that both the astm f2170 and the ambient air above it must be at service conditions for a minimum of 48 hours before testing.
Subscribe to Email Updates. Your email address will not be published. Astm f2170 News Technical Articles. September 2, at 9: Please login or create an account.
Public Knowledge Base
Added 08 Oct Author: All sensors astm f2170 be calibrated no less than 30 days prior to use. At this stage, the probes can be removed and the sleeves capped until further testing is required before mitigation can be carried out. RH Testing and Reporting Drill and prepare the test holes. Astm f2170 humidity RH in a concrete slab can fluctuate with environmental changes.
ASTM F Explained – ASTM F Information
Thanks for the reply, Patrick. And f270 are finding results are more accurate and more dependable with RH testing. These requirements for the standard apply regardless of the RH test method being used. The next five have to do with the proper installation and use of the RH test method.
F requires three test holes for the first ft 2 and, at least, one additional hole for each additional ft 2. Without it, even a well-dried and astm f2170 foundation can end up with concrete slab moisture problems. We recommend placing the serial number decal which also helps track certification of each sensor on the corresponding astm f2170 hole on the mapped report.
And moisture can still astm f2170 an issue at grade so concrete foundations must be designed to include proper moisture drainage. Under this testing standard, contractors drill holes in a concrete f21700 and insert sleeves that are then sealed. Some inexperienced individuals try to use a pin moisture meter for concrete floor testing rather than following the rigorous ASTM standard.
This will NOT be valid for ASTM compliance, but can certainly provide a astm f2170 timeline for schedule decisions or for choosing alternate adhesive or flooring options astm f2170 might have astm f2170 moisture tolerances.